Partial list of this Maytag Laundry Center components
(for additional details, please see All Parts & Diagrams
Washer/dryer control panel parts parts are sheet, cycle feature switch, push-to-start knob, timer (washer) buzzer, mini end cap (rh) receptacle spacer-foam pad (2) spring-clip knob end cap (lh) timer, dryer. Dryer front panel and door parts is composed of screw, 8-18 x 3/8 screw, 10-16 x 1/2 door, rear clip, ground clip, harness door, front handle, door strike, panel panel, front seal, door. Dryer cabinet and motor parts is composed of top, dryer washer, thrust panel, side (l.h.) panel, transition bracket, motor pulley, motor (60 hz.) bolt, shoulder clip, ground spacer (2) bracket, terminal block. Dryer bulkhead parts parts are screw, 10-16 x 1/2 clip, strain relief seal, drum thermostat, internal-bias lint duct assembly (includes illus. 7 & 13) shaft, roller clip, thermostat housing, blower shaft, l.h. thread housing, outlet. Dryer support and washer harness parts section includes block, disconnect - timer screw, 10-16 x 1/2 nut, hex (4) block, disconnect shield, thermostat plug, 3 way hose, pressure switch protector, harness connector, h-pod shield, front. Washer top and lid parts parts are locator, top bumper, lid (2) top, console strike, lid dispenser, bleach lid switch, lid hinge, bearing (2) hinge, r.h. hinge, l.h.. Washer cabinet parts is composed of foam bracket, base link, leveling clamp, hose clip, spring top (2) plug, top to cabinet (2) foot, front (2) rail, back top spring, lever bracket clamp, hose. Brake, clutch, gearcase, motor and pump parts parts include clip, anti-rattle plate, motor mount to gearcase screw, 10-16 x 5/8 washer, spin tube thrust brake and drive tube (complete) retainer, motor (2) ring, retainer retainer, pump clamp, capacitor capacitor, motor start. Machine base parts is composed of screw, bracket mounting (10-16 x 1/2) base assembly (include items, 11 & 18 ) spring, suspension (3) seal, centerpost (3) bracket, spring outer (l.f.) bracket, spring outer (2) washer (2) screw, shoulder (2) retainer, suspension spring screw, 10-32 x 5/8. Agitator, basket and tub parts parts include tub gasket, centerpost agitator washer gasket, tub ring hose & clamp assembly nut, spanner dog, agitator (4) agitator (complete) seal, inner cap. Gearcase parts section contains washer kit, thrust ring, retaining (2) cover, gearcase spring, agitate bearing, thrust (includes 18) neutral assembly washer, cam thrust cam, agitate (includes 13) actuator, shift washer, agitate gear. Brake and drive tube parts components are seal, drive tube shoe, brake (2) ring, retaining sleeve, brake spring t" bearing, spin tube spring, brake ring, thrust sleeve, cam ring, retaining cap, brake spring (2). Water system parts section includes clamp, hose (2) hose, corrugated plastic drain (5 1/2 ft.) connector kit, plastic drain hose u-bend sleeve kit, plastic drain hose (contains 2 sleeves) hose, corrugated plastic drain (6 1/2 ft.) (for fsou & twin-twin) siphon break kit (not included) clamp, hose hose, inlet (2) connector, straight. Miscellaneous parts section contains clamp, hose miscellaneous parts bag clamp, hose washer, inlet hose clamp, hose. 3402855 burner assembly components are conversion kit (type 1, 2 & 3) to type (4) l.p.g. supply line (gas) pipe coil, 60 hz. (split) coil, 60 hz. screw and washer 8-32 x 1 nut ignitor nipple, short bracket, shunt. Optional parts (not included) components are paint, touch-up (1/2oz.) (white) connector (3) position gas valve sealer, gasket (.20 fl. oz.) (6 ml) oil, gearcase (16 oz.) lubricant (use only in brake shoe assembly on roller and pin) kit, side exhaust connector edge paint, pressurized spray (12 oz.) (white) connector (2) position gas valve connector (pts) relay.