Control panel section contains screw switch button, switch (white-middle)(mde8600ayw,azw,md... pressure switch console (wht) (series 10) panel, control (wht) (series 10) button, switch (white-end)(mde8600ayw,azw,mdg86... back, console panel (series 10) tube, water level (airdome) (series 14) (non-il... screw. Top section contains hinge bushing cover guide tube plunger hinge lid cam (white) (series 12) hinge pin (wht) (qty 2) (series 18) screw power cord cover. Tub section includes tub gasket screw, shoulder (qty 4) (series 10) agitator auger seal, tub top - series e agitator auger outer tub tub block dispenser dispenser, fabric softener (incl. dispenser cup... seal, tub to housing - series e. Base parts include foot & pad assembly (front) (qty 2) (series 10) drive belt flat washer clip, lower front panel (qty 2) (series 10) (no... pump-water screw base (as packed) (series 12) spring, motor pivot (series 12) pump assem motor, 2sp 1/2hp 120/60 hi-tor (series 10). Transmission section includes spring bearing tub seal tub brace lip seal repair kit (series 10) screw brake spring lower bearing ht trans s housing, suspension (qty 6) (series 10) brake rotor. Wiring information parts are wiring information (series 10). Cabinet (prior ser pre 18) components are shipping stop cabinet drain cover inlet gasket sleeve tie, beaded (hdwr.pkg.) (series 10) (non-illus) washer (hdwr injector flume assy. not used at series 15 (ser... injector hose clamp, spring (series 10). Cabinet (ser pre 18 & after) section contains clip, air dome hose (series 18) (non-illus) shipping stop inlet gasket front panel inlet screw screw drain cover hose clamp cabinet.
What is the Maytag Atlantis Top Load Washer MAV6200AWW tub capacity?
Tub Capacity as per Manufacturer Specifications (in cubic feet):
The manufacturers began using cubic feet capacity numbers only recently.
Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load")
which did not take into account different fabric weight and volume. Others referred to capacity in
terms of water used. Even washers available today do not have capacity written in the manual because the same manual
can be used across multiple models. Once the washer is no longer sold, the sales literature is discarded
and capacity information often lost.
Analyzing washers and their components, searching through old technical information and sales literature, and
determining their capacity is a labor intensive and time-consuming task and we are far from finished.
A small charge will help us continue our research.
Consider this: if you were to spend more than four minutes looking for tub capacity on the internet, you
would be earning LESS than minimum wage.
Calculate Washer Tub capacity
This is a geometric method to calculate tub capacity based on the cylinder volume formula.
Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.
Why? Because the tub is not exactly a cylinder. The edge where bottom connected to the wall
is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and
the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.
This method can be used as a crude estimate but we do not recommend using it for comparisson
when shopping for a new washer.
Determine your washer tub capacity by taking two simple measurements:
1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)
2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some tubs are narrow
on top. In this case make the measurements INSIDE the tub.
Tub Depth: in. Tub Diameter: in.
The Maytag Atlantis Top Load Washer MAV6200AWW tub capacity is ... cubic feet.