Partial list of this Kenmore Laundry Center components
(for additional details, please see All Parts & Diagrams
parts are toast golden harvest almond leveler (thinner) label, wiring diagram platinum (uncut) almond (uncut) instructions, installation white white. Washer/dryer control panel components are switch, water level motor, timer (60 hz.) sleeve, console lock screw switch, push-to-start end cap, console (l.h. & r.h.) screw, dryer timer mounting (8-32 x 5/16) screw, timer mounting strut, console knob, timer switch, water temperature. Dryer front panel and door parts include almond fastener, push lever, door switch white clip, felt pad strike, panel toast golden harvest support white. Dryer cabinet and motor parts are panel, transition pulley, motor (60 hz.) clamp, capacitor idler & bracket platinum screw, capacitor mounting (10-16 x 1/2) clip, ground golden harvest toast elbow, lower. Dryer bulkhead parts include support, corner gas air duct & cover lint screen clip, strain relief thermostat, heater box 696707 (alt.) 341196 (alt.) screw, 10-16 x 1/2 receptacle, multi-terminal (connects with thermostat & heater harness) screw, 8-18 x 1/2 receptacle, terminal (2-way) (connects with automatic console harness) cover, manifold. Dryer supports and washer cabinet harness parts are clip, pressure switch hose wire, ground block, disconnect (connects with automatic washer motor) support, dryer (r.h.) cover, channel clip, wiring harness support, dryer (l.h.) plug, terminal (3-way) (connects with automatic lid switch harness) harness, upper (automatic) (includes illus. 6a, 6b & 6c) nut, 10-24. Washer top and lid section contains actuator, lid switch shield, lid switch bumper, lid screw, ground (10-24 x 1/2) hinge, lid (l.h.) spring, lid (r.h.) (includes illus. 10) white golden harvest almond switch, lid 388322 (alt.) 3347287 (alt.) 359230 (alt.). Washer cabinet is composed of plug, top to cabinet 689587 (alt.) 694010 (alt.) lock, top clip, leveling mechanism foam clamp, hose 272858 (alt.) 370447 (alt.) 353097 (alt.) siphon break screw golden harvest hose, drain screw, mixing valve mounting (10-16 x 3/8). Brake, clutch, gearcase, motor, and pump components are plate, motor mount to gearcase retainer, pump ring, spin tube support coupling, motor & isolating brake and drive tube (complete) (refer to sub asm. for further breakdown) cap, clutch spring grommet, motor screw, 5/16-24 x 3/16 (gearcase to tub support) spring, clutch gearcase (complete) (refer to sub asm for further breakdown). Machine base parts include tub support and drum screw, 8a x 3/8 bearing, centerpost centerpost bearing kit (incls. illus. 10, 11, & 12) bracket, counterweight spring shield, tub screw, 10-16 x 5/8 suspension assembly base spring, counterweight. Tub and basket parts include stopper hose, pressure switch seal, agitator hose, tub to pump clamp, hose block, basket drive gasket, tub ring basket nut, spanner screw & washer (5/16-24 x 1). Washer water system parts include coupling, hose hose, corrugated plastic drain (10 ft.) (not included) connector, hose sleeve kit, plastic drain hose (contains 2 sleeves) retainer, drain hose siphon break kit (not included) hose, corrugated plastic drain (5-1/2 ft.) hose, inlet 81339 (alt.) 366108 (alt.) connector, straight clamp, hose. Sales accessory (lck 4500) parts are exhaust deflector kit (complete) screw, mounting (10-16 x 1/2) (hex washer head). Sales accessory (lck 4600) parts are screw, 10-16 x 1/2 (hex washer head) side exhaust extension kit (complete). Miscellaneous parts include miscellaneous parts bag washer, inlet hose clamp, hose tie, cable foot, rear retainer, wire foot, front.